题号 | 维修常见问题 |
1 | AN ERROR IN DAC INITIALIZATION HAS OCCURRED |
2 | AN TIMING ERROR IN DAC INITIALIZATION HAS OCCURRED |
3 | DAC INITIALIZATION ERROR |
4 | A DAC INITIALIZATION ERROR INDICATES THAT GLUCOSE ELECTRODE MUST BE RECHARGED |
5 | AN ERROR IN ADC SEQUENCE TIMING HASS OCCURRED |
6 | AN DAC TIMEOUT ERROR HAS OCCURRED |
7 | CALBRATION CANCELLED – A RUN TIME DIGNOSTIC ERROR WAS DETECTED |
8 | INSUFFICIENT REAGENT STRENGTH - BUN |
9 | INSUFFICIENT REAGENT STRENGTH - GLU |
10 | ERRATIC ADC |
11 | AN ROTATIONAL ERROR HAS OCURRED FOR THE SAMPLE CRANE |
12 | AN ERROR HAS OCCURRED IN RAISING THE SAMPLE CRANE |
13 | AN ERROR HAS OCCURRED IN LOWERRING THE SAMPLE CRANE |
14 | SAMPLE DETECTED IN THE UP POSITION |
15 | NO SAMPLE DETECTED |
16 | AN ERROR HAS OCCURRED ON PINCH VALVE “ E ” |
17 | AN ERROR HAS OCCURRED ON PINCH VALVE “ C ” |
18 | AN HOME ERROR HAS OCCURRED FOR THE RATIO PUMP. |
19 | AN ASPIRATE ERROR HAS OCCURRED FOR THE RATIO PUMP. |
20 | SAMPLE WHELL HOME ERROR |
21 | SAMPLE WHELL POSITION ERROR |
22 | CX3 / CX3* MDR BOARD |
23 | EXCESSIVE REFERENCE DRIFT |
24 | GLUCOSE GAIN ERROR |
25 | NOISE IN CREATININE ABSORBANCE INDICATES BUBBLES IN THE CUP CREA – URINE MODE LOW |
26 | CREATININE – URINE MODE TOO LOW |
27 | CAN NOT BOOT |
28 | MMC NOT READY TO RECEIVE |
29 | MMC CHECKSUM ERROR |
30 | A SOFTWARE QUEUE ERROR HAS OCCURRED |
31 | A DATABASE CROSS-CHECK HAS FAILED |
32 | A SERIOUS ERROR IN DISK OPEARATION HAS OCCURRED |
33 | FIRST SAMPLE LOW |
34 | CA/CREA LAMP IS DARK |
35 | CX3 CAL ERROR |
36 | RANGE ERROR：
NA/K/CL/CO2，BUN/GLU/CA/CREA |
37 | BACK TO BACK – NA / K / CL / CO2 |
38 | INJECTION CUP FLOODING |
39 | CALIBRATION FAILURE：OCR HIGH |
40 | 校正FAILURE: OCR LOW |
41 | BAD PRECISION: CX3 / CX4 |
42 | ISE DATA BAD PRECISION (离子资料不准确) |
43 | MOTION ERROR – SAMPLE PROBE UP/DOWN ERROR (样品针上下的错误) |
43 | MOTION ERROR – SAMPLE PROBE ROTATE (样品针轮换的错误) |
44 | MOTION ERROR – SAMPLE MIXER UP/DOWN (样品搅拌器上下的错误) |
44 | MOTION ERROR – SAMPLE MIXER ROTATE (样品搅拌器轮换的错误) |
44 | MOTION ERROR – SAMPLE MIXER SPIN (样品搅拌器旋转的错误) |
45 | MOTION ERROR – REAGENT PROBE UP/DOWN (试剂针上下的错误) |
45 | MOTION ERROR – REAGENT PROBE ROTATE (试剂针轮换的错误) |
46 | MOTION ERROR – REAGENT MIXER UP/DOWN (试剂搅拌器上下的错误) |
46 | MOTION ERROR – REAGENT MIXER ROTATE (试剂搅拌器轮换的错误) |
46 | MOTION ERROR – REAGENT MIXER SPIN (试剂搅拌器旋转的错误) |
47 | MOTION ERROR – REAGENT CAROUSEL |
47 | MOTION ERROR – SAMPLE CAROUSEL |
48 | MOTION ERROR – AUTOLOADER UP/DOWN |
48 | MOTION ERROR – AUTOLOADER SPIN |
48 | MOTION ERROR – WASH STATION |
49 | MOTION ERROR - SAMPLE PROBE WASH, SAMPLE PROBE AIR STRIP, REAGENT PROBE WASH, REAGENT PROBE AIR STRIP, WASH TO CUVETTE WASH, CUVETTE VACUUM, WASH MIX VALVE |
50 | MOTION ERROR - SUMP PUMP, SIP VALVE, VACUUM RESERVOIR DUMP, DI WATER MIXER VALVE, WASH TO ISE, DI WATER TO CUVETTE WASH |
51 | MOTION ERROR - MIX BOTTLE 1, MIX BOTTLE 2, SAMPLE PROBE WASH, SAMPLE PROBE AIR STRIP, REAGENT PROBE WASH, REAGENT PROBE AIR STRIP. |
52 | MOTION ERROR – REACTION CAROUSEL |
53 | MOTION ERROR – SAMPLE VALVE, SAMPLE PUMP, REAGENT VALVE, REAGENT PUMP |
54 | REAGENT DOOR IS OPEN |
54 | PROBE RINSE 没消耗 |
54 | WASH BOTTLE 没充水 |
55 | AUTOLOADER TIMEOUT |
56 | MOTION ERROR - BAD MESSAGE INTERRUPT ON MMC； UNDEFINED MSB ERROR；NO GOLDEN PHASE ON REAGENT；NO GOLDEN PHASE ON SAMPLE；NO GOLDEN PHASE ON REAGENT CAROUSEL；NO HOME ON REAGENT；NO HONE ON SAMPLE； NO HOME ON REAGENT CAROUSEL. |
57 | MOTION ERROR - ERROR IN MMC COMMUNICATION；BAD PACKET CHECKSUM；MAC PROCESSOR OR EPROM FAILURE； CHECKSUM ERROR IN MSC DOWNLOAD；
BAD INIT HANDSHAKE WITH MSC. |
58 | MOTION SYSTEM IS BUSY: BAD ALIGNMENT DATA DETECHED |
59 | MOTION ERROR – CX3 PROBE NOT CLEAR |
60 | AIR PRESSURE OUT OF RANGE |
61 | WATER PRESSURE LOW/HIGH |
62 | LIQUID TRAP TOO HIGH |
63 | VACUUM BOTTLE FULL WATER |
64 | VACUUM PRESSURE LOW |
65 | SECONDARY PRESSURE LOW/HIGH |
66 | DI WATER LEVEL LOW |
67 | POWER SUPPLY FAILURE |
68 | PRINTER NO FUNCTION |
69 | CUVETTE FAILED WATER BLANK TEST |
70 | SECTOR CAN’T CLEAR |
71 | SECTOR NOT RUN |
72 | CABTRADGE CAN’T AUTOLOAD |
73 | WASTE BUCKET FULL |
74 | COMPRESSOR NO ACTION |
75 | BUBBLE GENERATOR NO BUBBLE |
76 | REAGENT PROBE LEAK |
77 | SAMPLE PROBE 滴水或悬水珠 |
78 | WASH CUP 有水汽喷出 |
79 | SAMPLE NOT DETECTED |
80 | REAGENT NOT DETECTED AT SAMPLE INJECTION |
81 | PELTIER FAILURE |
82 | PELTIER TEMPERATURE |
83 | CX3 POWER SUPPLY |
84 | ISE POWER SUPPLY FAILURE |
85 | DBM FATAL ERROR # 0, # 8, # ? |
86 | ANALOG CONTROL SENSOR ERROR |
87 | ANALOG COMMUNICATION ERROR |
88 | ANALOG COMMUNICATION ERROR |
89 | FATAL MMC ERROR |
90 | CHECKSUM ERROR STACK OVERFLOW HARDWARE MEMORY |
91 | MMC TIMEOUT ERROR |
92 | UNRECOGNIZED COMMAND SENT TO MMC |
93 | PHOTOMETER SYSTEM NOT READY |
94 | ANALOG WAS DEAD- AT INITIALIZATION |
95 | FATAL ERROR – IOM MODULE |
96 | FATAL ERROR - COULD NOT POST ALARM EVENT, ALARM REQUEST LIST FULL, COULD NOT OPEN ALARM REQUEST QUEUE, COULD NOT OPEN EVENT QUEUE; COULD NOT CREATE ALARM AQENT TASK; COULD NOT POST ALARM REQUEST; COULD NOT REPORT ALARM EVENT; ALARM NOT RUNNING. |
97 | SCSI PROBLEM |
98 | CAN’T START HEATER CALIBRTION CODE |
99 | DOES NOT MATCH DATA ON DISK |
100 | INCOMPATIBLE TEMPERATURE BOARDS |
101 | CANNOT START: FATAL ANALOG ERROR |
102 | CANNOT START: CX4 ANALOG SYSTEM NOT READY |
103 | CANNOT START: DATABASE ERROR |
104 | ERROR SYNCHRONIZING CX3 (ISE) PROBE AND CX4 SAMPLE CAROUSEL ASTAR |
