注册登录才能更好的浏览或提问。
您需要 登录 才可以下载或查看，没有账号？立即注册
×
BECKMAN INSTRUMENTS INC.
LX-20 System Boot
Copyright 1997 Beckman Instruments Inc.
Copyright 1984-1993 Wind River Systems, Inc.
CPU: Motorola MVME162
Version: 5.1.1
BSP version: 1.0
Revision Date: 14-Feb-97
Checked DRAM [0x00001008 to 0x007FFFFF]......OK
Checking FLASH memory integrity......
IccHeaderRec = ff8fffd0
CheckFullImageCRCs: mem start addr 0xff800000
CheckFullImageCRCs: stored crc 0x60d5 vs calculated crc 0x60d5
CheckFullImageCRCs: stored crc 0xb122 vs calculated crc 0xb122
CheckFullImageCRCs: stored crc 0x37da vs calculated crc 0x37da
CheckFullImageCRCs: stored crc 0xcc2 vs calculated crc 0xcc2
CheckFullImageCRCs: stored crc 0xd6cf vs calculated crc 0xd6cf
CheckFullImageCRCs: stored crc 0xf2fa vs calculated crc 0xf2fa
......OK
Checking TOD bbram config memory integrity......OK
------------------------------------------------------------------
If the TOD bbram has a checksum error, a Service Document
describing how to fix this problem is available.
------------------------------------------------------------------
Checking IP bus DPRAM 0 memory integrity......OK
Checking IP bus DPRAM 1 memory integrity......OK
ICC POWERUP DIAGNOSTICS COMPLETE
Press any key to stop auto-boot...
7 6 5 4 3 2 1 0
auto-booting...
Wrote 1 to semaphore location 0xfff58000 - fff58010
Wrote 1 to semaphore location 0xfff58200 - fff58210
----------------------------------------------------------------
If the boot parameters below are incorrect, a Service Document
providing the correct values and a procedure for fixing the
values is available.
----------------------------------------------------------------
boot device : ei
processor number : 0
flags (f) : 0x1c0
startup script (s) : /usr/local/startup.bat
other (o) : 134.217.96.176
-----------------------------------------------------------------
The other (o) field may be empty or it may contain the IP address
for the console.
If the ICC cannot communicate with the console, the ICC will
restart the autoboot process at this time. When the console
is at Hardware Diagnostics, the console is ready to communicate
with the ICC. If the console is not at Hardware Diagnostics,
the ICC will continue to reboot until the console reaches
Hardware Diagnostics.
-----------------------------------------------------------------
Attaching network interface ei0... done.
Getting boot parameters via network interface ei0.
Bootp Server:134.217.96.176
Boot file: /cauvan/boot/cau/bin/msmcload
Boot host: 134.217.96.176
Boot device Addr (ei0): 134.217.97.101
Subnet mask: 0xfffffc00
Attaching network interface lo0... done.
BOOTROM: WAITING for RebootMonitor to connect to Console
RebootMonitor-binded client socket
RebootMonitor-premoteAddr 134.217.96.176 = 0x86d960b0
RebootMonitor-connected to 134.217.96.176 on port becb
RebootMonitor-turning non-blocking I/O on
Start downloading binary 0
params.had = 7f89b4 134.217.96.176
-binded client socket
-premoteAddr 134.217.96.176 = 0x86d960b0
-connected to 134.217.96.176
-turning non-blocking I/O on
[[[[[[[[[[[[ No hardware errors ]]]]]]]]]]]]]]]
Sending HARDWARE_OK message to MPC
pwrupmsg.function = 0
pwrupmsg.length = 64
pwrupmsg.errnum = 0
sizeof(pwrupmsg) = 110
DownloadBootImage: GetBootImageParams...
SendMsg: [len,fcn,errid,errstr] 0 0x20 0 (null)
DownloadBootImage: NotifyBegin...OK
CheckHeaderCRC: crc = 0
DownloadBootImage: GetHeaderRec...OK
StoreHeader: full image len = 0x25bce4
100K
200K
300K
400K
500K
600K
700K
800K
900K
1000K
1100K
1200K
1300K
1400K
1500K
1600K
1700K
1800K
1900K
2000K
2100K
2200K
2300K
2400K
DownloadBootImage: DownloadDataRecs...OK
CheckFullImageCRCs: mem start addr 0x1000
CheckFullImageCRCs: stored crc 0x5378 vs calculated crc 0x5378
CheckFullImageCRCs: stored crc 0x9fa3 vs calculated crc 0x9fa3
CheckFullImageCRCs: stored crc 0x7ac2 vs calculated crc 0x7ac2
CheckFullImageCRCs: stored crc 0xa81f vs calculated crc 0xa81f
CheckFullImageCRCs: stored crc 0xd7d9 vs calculated crc 0xd7d9
CheckFullImageCRCs: stored crc 0x173d vs calculated crc 0x173d
DownloadBootImage: CheckFullImageCRCs...OK
SendMsg: [len,fcn,errid,errstr] 0 0x11 0 (null)
DownloadBootImage: NotifyEnd...OK
Entry point returned is 1000
Done downloading binary 0
Starting at 0x1000...
Host Name: bootHost
Target Name: vxTarget
User: lx20
Attaching network interface ei0... Done.sir1891
ifAddrSet : ifname = ei0, inetAdrs = 134.217.97.101
calling hostAdd
Wrote 1 to shared mem. semaphore for MSMC 0
usrBpInit- Initializing backplane net with anchor at 0x801000... Done.SIR1891
usrBpInit- Backplane anchor at 0x801000... usrBpInit - END
Attaching network interface sm0... Done.sir1891
ifAddrSet : ifname = sm0, inetAdrs = 134.217.97.102
In BOOT STATE: skipping semaphore checking
In BOOT STATE: skipping semaphore checking
Wrote 1 to shared mem. semaphore for MSMC 1
usrBpInit- Initializing backplane net with anchor at 0x821000... Done.SIR1891
usrBpInit- Backplane anchor at 0x821000... usrBpInit - END
Attaching network interface sm1... Done.sir1891
ifAddrSet : ifname = sm1, inetAdrs = 134.217.97.104
In BOOT STATE: skipping semaphore checking
In BOOT STATE: skipping semaphore checking
Creating proxy network: 134.217.97.104
Creating proxy network: 134.217.97.102
Attaching network interface lo0... Done.sir1891
ifAddrSet : ifname = lo0, inetAdrs = 127.0.0.1
calling hostAdd
NFS not included.
--------------------------------------
| Bootstrap, Check, and Load MSMC 0 |
--------------------------------------
Phase 1 - BOOTSTRAP
Opening bootstrap file.https://www.yeec.com/cauvan/boot/cau/bin/msmcload ......OK
Allocating buffer ......OK
Reading file...OK
Copying file to MSMC module......OK
Starting MSMC module ......OK (board running)
Opening MSMC boot file.https://www.yeec.com/cauvan/boot/cau/bin/bootrom_uncmp ......OK
Phase 2 - CHECK
Checking chip Internal DPRAM for MSMC 0 ......OK
Checking and Zeroing MSMC 0 DRAM ......OK
Phase 3 - LOAD
Copying /cauvan/boot/cau/bin/bootrom_uncmp to MSMC module ......OK
--------------------------------------
| Bootstrap, Check, and Load MSMC 1 |
--------------------------------------
Phase 1 - BOOTSTRAP
Opening bootstrap file.https://www.yeec.com/cauvan/boot/cau/bin/msmcload ......OK
Allocating buffer ......OK
Reading file...OK
Copying file to MSMC module......OK
Starting MSMC module ......OK (board running)
Opening MSMC boot file.https://www.yeec.com/cauvan/boot/cau/bin/bootrom_uncmp ......OK
Phase 2 - CHECK
Checking chip Internal DPRAM for MSMC 1 ......OK
Checking and Zeroing MSMC 1 DRAM ......OK
Phase 3 - LOAD
Copying /cauvan/boot/cau/bin/bootrom_uncmp to MSMC module ......OK
Launching MSMC 0 ......OK (running)
Launching MSMC 1 ......OK (running)
SPAWNING RebootMonitor
Adding 4968 symbols for standalone.
RebootMonitor-binded client socket 9
RebootMonitor-premoteAddr 134.217.96.176 = 0x86d960b0
RebootMonitor-connected to 134.217.96.176 on port becb
RebootMonitor-turning non-blocking I/O on
RebootMonitor - POLLING MPC
Saved windviewlog.wvr to console
CPU: Motorola MVME162. Processor #0.
Memory Size: 0x800000. BSP version 1.0.
Executing startup script /usr/local/startup.bat ...
#/****************************************************************************
# *
# * * * * * * * B E C K M A N I N S T R U M E N T S , I N C. * * * * * * * *
# *
# *
# * Module Name: startup.bat
# * Date First Written: 06/04/93
# * Project: Vanguard
# * Purpose: startup script for the ICC (040) MV162
# *
# * Change History:
# * REF # DATE AUTHOR DESCRIPTION
# * ----- -------- ------ ------------------------------------------------
# * .01 06/04/93 WRS First cut.
# * .10 09/27/93 MM,CM Subsystem Release 0.1
# * .20 10/20/93 CM,MM Subsystem release 0.2
# * .21 11/10/93 DD,MM Fixed problem with cold booting of ICS
# * .22 12/16/93 CM Call ICC bootup script to set environment
# * .30 12/20/93 CM Subsystem Release 0.3
# * .31 04/14/94 CM Modify to wait for MSMCs to notify ICC when
# * done booting.
# * .32 08/03/94 CM Modified to call bootp versions of setup() and
# VanBoot()
# * .33 10-OCT-94 MM Added loading of barcode interface library.
# * .34 17-Nov-94 CM Removed loading of barcode interface.
# Now done in set_phase()
# * .35 22-NOV-94 MM Added 'mpc' to the host table.
# * .36 09-DEC-94 MM external comm. shutdown for integration testing.
# * .37 10-JAN-95 MM Removed External Comm. Shutdown.
# * .38 10-JAN-95 CM Changed bootup directory to EXP for testing.
# * .39 06-SEP-95 CM Modified to work with Central Server
# * sir1935 17 Jan 96 SMZ Removed for boot from MPC: appHost references;
# * homedir & photometer calib# params; set_phase,
# * load_VanApps & STMACH_StateMachine function calls;
# * abort breakpt. Changed: ppi-->target
# * sir3485 30-JAN-96 DL Add POWER_Shutdown to the end of the file.
# * sir1935 02 Feb 96 SMZ Change values of instrument#, udpip#, prompt.
# * Add "cd /cauvan/boot" to end.
# * sir3785 03-APR-96 DL Change user name to lx20.
# * sir2278 15-MAY-96 DL Add changes for vA4.1.
# * sir7032 24-DEC-96 DF Add disabling of reagent wheel door check
# * sir7143 24-DEC-96 DF Add spawning of VanBoot task
# * sir7033 30-MAY-97 DF Remove disabling of reagent wheel door check
# * sir7468 30-MAY-97 DF Remove setting of F_MATRIX env variable
# * sir8052 17-SEP-97 DF Remove calls to hostAdd() and netDevCreate()
# for the Datalogger/Service PC
# *sir10738 05-DEC-97 DF Add task suspend of RebootMonitor
# ****************************************************************************/
#
ts "RebootMonitor"
value = 0 = 0x0
putenv( "INSTRUMENT=LX-20" );
value = 0 = 0x0
setup( "134.217.96.32", "LX20->" )
value = 0 = 0x0
hostAdd ("mpc", "134.217.96.176")
value = 0 = 0x0
iam( "lx20", "lx20" )
value = 0 = 0x0
taskSpawn "tVanBoot",1,0x08,20000,VanBoot,'I'
value = 8013492 = 0x7a46b4
cd "/cauvan/boot"
------------Ins
value = 0 = 0x0
ide VanbootInit ------------
bootHost = 0x86d960b0
connected to bootHost
turning non-blocking I/O on
VanBoot: initia
Done executing startup script lizing DP/usr/local/startup.bat, SUBSYS, MEMORY,
ALIGN, CYCLE,
CHEMDB, SMPCRD, XCOM, ICOM, BOOT, START, POWER, RARW,
RGTWHL, SR, HYDRO, RARD, RASD, PPSD, RARS, PP, INSTMISC, SHUTDOWN...
LX20->tVanBoot: Opening stream 0 as UDP port 5001 on node 134.217.96.32
usrPktInit: Unit 0 descriptor 0x7c2ef6
usrPktInit: Unit 1 descriptor 0x7c2db2
XComSrvr: listening
XComClnt: connected to MPC at 134.217.96.176 on socket 16
XComSrvr: accepted a connection from 134.217.96.176 on socket 17
CommEventTask - Q = 5fd7a4
Waiting to connect to MSMC event logging
############ Waiting for MSMCs to be ready ...############
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 0 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 7 58 59 60 61 62 63 64 65 66 67
MSMC0 completed in 68 seconds
MSMC1 completed in 0 seconds
VanBoot: initializing STMACH, RASEQ, RASCHIF...
trgtwhlLSPT-BcrInit: PP barcode initialized OK
trgtwhlBCRT-BcrInit: RA barcode initialized OK
Turning parity off
Sending BREAKS now to Port B Tx
Done sending BREAKS to Port B Tx
Verifying Sample BCR Communications status. <KT?>
Verifying Sample BCR Setup status. <KU?>
Verifying Sample BCR Operations status. <KV?>
Verifying Sample BCR Code Type Symbology status. <KW?>
Verifying Sample BCR Scanner Output status. <KX?>
Build39: Verifying Code39 parameters modified ..... OK
BuildCodabar: Verifying Codabar parameters modified..... OK
BuildI2of5: Verifying I2of5 parameters modified..... OK
VERSION 1.1 ICC BOOT SEQUENCE | 
